Hi All
As title says, is it possible to cut for c-more RTS on the M&P slide or has anyone done that?
Cheers
Tom
Is it possible to cut for c-more RTS on m&p slide?
Started by
strikeraj
, Jul 23 2012 10:26 AM
5 replies to this topic
#2
michael1778
-
- Classifieds
-
- 422 posts
Sees Sights Lift
- Gender:Male
- Location:Clemmons, NC
Posted 23 July 2012 - 11:42 AM
Bowie Tactical has done it for the Leupold Deltapoint, so I would imagine the very same could be done for the RTS. That's not a confirmation, but at least some indirect support for the concept.
"Oh <bleep> it!!! I'll try shooting Open...."
Carbon Arms 16" upper on a Firebird lower that I built!! (Firebird comp, Vortex Viper PST 1-4x MOA - capped, MagPul MOE Rifle stock, AR Gold trigger, JP captured spring)
Remington Versa Max 26" (C-rums lifter/trigger/load port/rib sight, full-size XRAIL, extended Remington factory chokes)
S&W M&P 9mm Pro 5" (Burwell Competition trigger job, Burris Fastfire III - 8 MOA, SSS Limited mag well & Taylor Freelance +10 base pads)
Carbon Arms 16" upper on a Firebird lower that I built!! (Firebird comp, Vortex Viper PST 1-4x MOA - capped, MagPul MOE Rifle stock, AR Gold trigger, JP captured spring)
Remington Versa Max 26" (C-rums lifter/trigger/load port/rib sight, full-size XRAIL, extended Remington factory chokes)
S&W M&P 9mm Pro 5" (Burwell Competition trigger job, Burris Fastfire III - 8 MOA, SSS Limited mag well & Taylor Freelance +10 base pads)
#3
diehli
-
- Classifieds
-
- 5,436 posts
Geniass
- Gender:Male
- Location:Emeryville, CA
Posted 23 July 2012 - 12:20 PM
The RTS is a completely different beast. I'd guess it would not be an easy or inexpensive experiment, and that's assuming the RTS could withstand slide-mounting.
#4
strikeraj
-
- Members
-
- 22 posts
Looks for Range
Posted 29 July 2012 - 06:30 PM
Bowie Tactical has done it for the Leupold Deltapoint, so I would imagine the very same could be done for the RTS. That's not a confirmation, but at least some indirect support for the concept.
Thanks. But the RTS is a bit different because it has a built in weaver rail
The RTS is a completely different beast. I'd guess it would not be an easy or inexpensive experiment, and that's assuming the RTS could withstand slide-mounting.
Yea, i am just wondering if someone knows the rear end of the slide well and can say if there is enough room to do the cutting for the rail
#5
RWF
-
- Classifieds
-
- 668 posts
aka: wicked
- Gender:Male
- Location:McEwen, TN
Posted 29 July 2012 - 08:02 PM
if it worked it would be big and tall. you can only cut down to the cap on the safety plunger, and a rail would still be higher than the top of the slide. i do not know but i think that would increase the forces on the sight.
Wicked for my wonderfully wicked wife! 
#6
Chris iliff
-
- Classifieds
-
- 1,979 posts
aka: fourtrax
- Gender:Male
- Location:Peru, Indiana
Posted 30 July 2012 - 06:21 PM
I asked Cheely (very good smith) about doing this on an STI and he didn't recommend it. He didn't think it was designed to take slide mounted abuse.
Email Cmore and ask them. Post the answer.
Email Cmore and ask them. Post the answer.
Don't be a brown banana. Inspired by a Cocobolo comment.
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users
