Springfield 1911-A1 .40 s&w Single Stack Division Ready.
List price $3,550.00
The frame and slide are forged carbon steel, the barrel is a Nowlin ramped bushing barrel with a flush crown. EGW parts: slide stop-firing pin stop-hard sear-HD extractor-xl ejector-pins-guide rod-angled bored barrel bushing. SV ITS trigger system-wide ambi safety-barrel link. S&A-magwell and grip safety. Bo-mar rear sight with a Henning Wallgren front fiber optic sight.Ed Brown hammer strut. Koenig hammer, LimCat XL firing pin, C&S disconnector, Davidson's "Wrym" grips with ss hex grip screws. Welded frame rails for tighter fit, squared trigger guard and under cut, snake bellied top with flute borders, 40 lpi rear serrations, French border, dbl cocking serrations, beveled edges with thumb relief cut, 25 lpi checkering on the front and back strap and bottom of the trigger guard, magwell has a widened blend and back cut, grip safety blended and cut for a high hand hold, "Canyon Blue" finish on the upper with Metaloy hard chrome on the lower, 1-Wilson mag.
$3,650.00
SOLD
Springfield 1911-A1 9mm Single Stack
List price $3,550.00
The frame and slide are forged carbon steel, the barrel is a Nowlin ramped bushing barrel with a flush crown. EGW parts: slide stop-firing pin stop-hard sear-HD extractor-xl ejector-pins-guide rod-angled bored barrel bushing. SV ITS trigger system-wide ambi safety-barrel link. S&A-magwell and grip safety. Bo-mar rear sight with a Henning Wallgren front fiber optic sight.Ed Brown-mag release-hammer strut. Koenig hammer, LimCat XL firing pin, C&S disconnector, Ahrends "Apple Jack" grips with ss hex grip screws. Welded frame rails for tighter fit, squared trigger guard and under cut, snake bellied top with flute borders, 40 lpi rear serrations, French border, dbl cocking serrations, beveled edges with thumb relief cut, 25 lpi checkering on the front and back strap and bottom of the trigger guard, magwell has a widened blend and back cut, grip safety blended and cut for a high hand hold, "Canyon Blue" finish on the upper with Metaloy hard chrome on the lower, 1-Wilson mag.
Springfield 1911-A1 .38 super Single Stack
List price $3,250.00
The Super is finished, Springfield slide and frame was refit for a tighter fit, a Nowlin ramped barrel with an EGW thick flange barrel bushing and SV link, Heinie magwell w/G-10 grips and light weight trigger, squared trigger guard w/25 lpi checkering on the bottom and under cut, front strap and back strap are checkered in 25 lpi, S&A grip safety blended high, Wilson ambi, Nowlin "Pro" hammer and extended mag release, EGW parts are sear, pins, ejector, extractor, slide stop, and firing pin stop, Lim-Cat XL firing pin, 2 piece guide rod, "Bo-mar" rear sight with Henning Wallgren's front fiber optic, top of the slide has been snake bellied with flute borders, French border, 40 lpi serrations on the back of the slide, Edges are beveled, "Canyon Blue" finish, and one Wilson 10 round mag.38 super
Rock River Arms 1911-A1
List price $3,750.00
The frame and slide are forged carbon steel, the barrel is a Nowlin ramped bushing barrel with a flush crown. EGW parts: slide stop-firing pin stop-hard sear-HD extractor-xl ejector-pins-guide rod-angled bored barrel bushing. SV ITS trigger system-wide ambi safety-barrel link. S&A-magwell. Bo-mar rear sight with a Henning Wallgren front fiber optic sight.Ed Brown grip safety- hammer strut. Koenig hammer, LimCat XL firing pin, C&S disconnector, "Operator" grips with ss hex grip screws. Squared trigger guard and under cut, snake bellied top with flute borders, 40 lpi rear serrations, French border, dbl cocking serrations, beveled edges with thumb relief cut, 25 lpi checkering on the front and back strap and bottom of the trigger guard, magwell has a widened blend and back cut, grip safety blended and cut for a high hand hold, "Canyon Blue" finish on the upper with Metaloy hard chrome on the lower, 1-Wilson mag.
EAA/Tanfoglio Limited Pro .40 s&w Custom
List price $2,000.00
Next up is a Tanfoglio Pro Plus, this gun started as a Limited Pro in double action. Mods include Henning Wallgren's trigger system with EGW hammer and sear, Henning's firing pin-checkered grips blue-pins- front sight, it has the top snake bellied, angle slot side cuts and thinned, CC weld on magwell, factory checkering recut, bottom of trigger guard cut with 25 lpi checkering, the Pro has a standard sized barrel and short dust cover, Canyon Blue finish, one 21 round mag, factory hard case.
Firebird Precision AR 15 in 6.5 Grendel
List price $1,825.00
This is a custom rifle build on the 6.5 grendel cartridge, the receiver set is one of the first Firebird Precision FPX-15. The serial number on this one is FPX000007, I have number 8 if the buyer wants another rifle built. It has a Walther 24" 1x8 twist stainless barrel and bolt, a Thor comp and a EGW gas block. A JP V Tac hand guard(2 studs), Rock River Arms small parts, charge handle, and rubber grip(Hogue?), a Jard adjustable trigger, an Ace ARFX butt stock with Brownells buffer-spring and tube.
Springfield EMP 9mm
List price $2,850.00
The second gun is an EMP 9mm with the standard upgrades.
Heinie magwell with "Monkey Grips" black and gray wrym pattern, a custom made main spring housing with 25 lpi checkering that works with the mag well. The front lip of the mag well is ball cut for a positive little finger grip, the front strap is also checkered 25 lpi. The trigger guard is under cut and checkered 25 lpi. EGW HD single side safety and hard sear. Slide edges beveled and thumb relief cut, the top of the slide has the concave cut and 40 lpi serrations on the rear of the slide. French border added and Heinie rear sight added, the front is the stock tritium sight-pinned. I did two types of grip safeties, one is the factory and the other is a bobbed grip safety and bobbed hammer. The radius on these EMPs is a little large so the factory safety doesn't look as good as it should with the large gap present. The bobbed version should be easier to conceal, one shouldn't worry about hammer bite as there is plenty of room between the two parts. The frame is finished in KG Gun-Kote Titanium and the rest of the parts are "Canyon Blue". I do one flush fit mag and 2 factory mags.
Springfield EMP .40 s&w
List Price $3,100.00
The next gun up is a Springfield EMP in .40 s&w.
I take a new EMP and square the trigger guard-undercut and add 25 lpi checkering on the bottom, the front strap is checkered 25 lpi also, a Heinie magwell is added along with a custom main spring housing, the magwell area is widened and blended, the butt of the main spring housing is rounded for a better grip, Larry Davidson "Half Hog grips are used and fit and blended to the gun, the grip safety is under cut and blended for a higher grip, the back of the slide is serrated with 40 lpi, the top of the slide is snake bellied with flute borders, the barrel is crowned, edges are bevelled, a 10-8 lightened trigger is used, Nowlin "Pro" hammer, Heinie "Slat Pro" rear sight with the factory tritium front sight, the gun comes with 2 standard mags and one flush fit mag. The gun is finished in "Canyon Blue" finish.
Edited by RIIID, 15 April 2012 - 08:34 AM.
